Neb Powshape

[chrismp]

Unfortunately it was raining here too. The "Föhn" winds brought us warm temperatures and rain :/

As for the epoxy fully curing. I usually leave my board to cure for about 5 days before I cut the flash and finish them. Some epoxies can take up to 7 days to fully cure depending on the conditions.

For a heat cure epoxy I would recommend Sicomin Greenpoxy with their SZ8525 hardener. They are a french company, so should be easy to get in france.

[Buckow]

Unfortunately it was raining here too. The "Föhn" winds brought us warm temperatures and rain :/

As for the epoxy fully curing. I usually leave my board to cure for about 5 days before I cut the flash and finish them. Some epoxies can take up to 7 days to fully cure depending on the conditions.

For a heat cure epoxy I would recommend Sicomin Greenpoxy with their SZ8525 hardener. They are a french company, so should be easy to get in france.

Still raining?

Ok thanks! I will let them cure longer then!
I ordered some Sicomin sa 8525. I was already using the Surf Evo Clear and Greenpoxy from them but I hadn’t found the 8525 yet. I had it sent to a friend’s house just over the border in France.

Here’s my latest board finished. I put a bunch of flax and carbon in there. I haven’t ridden it yet but I think this one is the best one yet. This would be my 5th board but I taught 2 friends how to make one in my shop so 7 total but I made 5 of them. It is coming along and I’m enjoying it!

4ADE9814-023C-43F8-A196-5B78186C57F1.jpeg (621.18 KiB) Viewed 13478 times

550CB1A1-6538-4A75-BD7A-C6EEAAEAC31B.jpeg (634.95 KiB) Viewed 13478 times

6802E0DB-DB20-4F75-B1E1-00547F8B0391.jpeg (626.36 KiB) Viewed 13478 times

18D1FC62-F59E-491C-9AAA-0152F550753E.jpeg (621.5 KiB) Viewed 13478 times

013FB826-1870-4E1B-B35A-12A579675E11.jpeg (632.25 KiB) Viewed 13478 times

[Buckow]

And a riding pic before the rain.

88178474-B85B-4C53-B760-52D4D2C141C9.jpeg (404.21 KiB) Viewed 13477 times

[chrismp]

Fortunately not! No new snow either though haha.

The new board looks great...the wavy parts of the flax/carbon almost look like wood grain.

[pmg]

Oooh there was plenty of rain here. We had 80cm of dry snow on frozen ground in the valley, now its vanished ;(

Great Picture! Where was it taken?

[Arno]

Great picture, is was in Val d'Isère ?
séjour de ski Courchevel, France
Ce serait certainement un défi de skier les 600 km des Trois Vallées de Courchevel en un week-end, mais il est bon de viser haut.
L'Hôtel Olympic, l'hébergement de courte durée de Ski Solutions, est situé dans la ville très prisée de Courchevel 1850, à une minute des pistes. Indispensable si vous voulez couvrir tout ce terrain.

[Buckow]

Great picture, is was in Val d'Isère ?


Thanks! No, that was in Les Crosets, Suisse.

Yesterday was the last day of the season here and here’s the last board I built this year. I tried some wood veneer for the first time. It came out pretty good!

D702917D-22B5-44F4-9AB6-B83D37C28F0A.jpeg (499.79 KiB) Viewed 13244 times

These are from a few weeks ago on the second to last board with the flax and carbon.

https://youtu.be/51YkhZ10kYk
https://youtu.be/y4BtytZOu24

[Buckow]

Unfortunately it was raining here too. The "Föhn" winds brought us warm temperatures and rain :/

As for the epoxy fully curing. I usually leave my board to cure for about 5 days before I cut the flash and finish them. Some epoxies can take up to 7 days to fully cure depending on the conditions.

For a heat cure epoxy I would recommend Sicomin Greenpoxy with their SZ8525 hardener. They are a french company, so should be easy to get in france.

Thanks for the tip on the Sicomin sz8525! That stuff is so much easier to work with than all the others I’ve tried. I really like it! It cures so fast at 90*.

[chrismp]

Cheers! Glad you like it!

Nice new board...looks like it has a little "spoon" in the nose?

[Buckow]

Cheers! Glad you like it!

Nice new board...looks like it has a little "spoon" in the nose?

Thanks @chrismp ! That one rides the best so far. I’ve had some incredible days lately on that board!

No spoon nose but the tip spacer somehow didn’t want to sit flush with the core and climbed up on it. I managed to get this new one to sit flat by using epoxy instead of super glue when sticking the core and tip spacer together.

Here are some pics from the last few days. I’m getting some epoxy creeping under the edges on the nose, tail and ends of the effective edges. I wonder if I might have too much tension in the edges and they are not sitting perfectly flat? I’ll try and have the edges perfect next time around….

Walnut top sheet with Beech sidewalls and a Paulownia core.

AD6BEC59-5F16-4529-8038-DB7420E34BDF.jpeg (422.04 KiB) Viewed 12006 times

1CEFF009-2F08-4BB4-A840-B47AFB51A2A6.jpeg (499.67 KiB) Viewed 12006 times

930BE683-63B5-4A57-AF93-E2FD708064F1.jpeg (264.26 KiB) Viewed 12006 times

3C5A864E-174A-481F-915D-CD57AFC43F49.jpeg (619.19 KiB) Viewed 12006 times

[Buckow]

The new board is a little soft but carves so good and is super nice in the powder. I think I will make the core a tiny bit thicker on the next one. Here’s a pic from 2 days ago.
I’m not sure why there are 2 of the same photo.

A010B8D1-2352-42B5-8B45-8AD7F31B2208.jpeg (272.62 KiB) Viewed 11904 times

A010B8D1-2352-42B5-8B45-8AD7F31B2208.jpeg (272.62 KiB) Viewed 11904 times

[chrismp]

Sweet! I was at Corvatsch on new years - unfortunately not nearly the amount of snow you guys have now haha