Forum Index

 
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

Slant Skis is Selling Complete Ski Press - Tahoe City, CA

 
Post new topic   Reply to topic     Forum Index -> Commercial postings
View previous topic :: View next topic  
Author Message
Slant



Joined: 16 Apr 2009
Posts: 34
Location: North Lake Tahoe

PostPosted: Mon May 30, 2016 2:33 pm    Post subject: Slant Skis is Selling Complete Ski Press - Tahoe City, CA Reply with quote

Hi Ski Builders,
--for pictures-->http://tahoesnowlab.com/ski-press

We are selling our trusty ski press. We have pressed hundreds of pairs of skis with this press. It is in complete working order. The new one we are designing is the same as this, except it will be double decker so we have a more efficient space.

The rigid opening is 18" deep x 11" high x 76" across between the vertical posts. The entire press is 8' across and 67" high. You can press with the entire 8' (240+ cm), but it's easiest to access the mold from the side pressing 200cm + skis.

The press is made of twin I-beams top and bottom. There is 3/16 plate top and bottom, spanning the beams. It is bare steel.

It is on heavy duty casters so you can push it....slowly. It weighs about 1,700 lbs. But you can bring it with you wherever you want to go!

We usually press at about 45 psi. We have calculated the pressure at around 22 tons.

I will include our temperature control setup along with a newer heat mat. We usually press around 180º F. This controller will allow you so set whatever temp you want. It runs off single-phase 220V power for the heat and 110v for the controller.

I will include our 1/2" square tube cat-track.

The industrial grade goodyear fire hoses are included too. Along with the air hoses and pressure gauge. Just plug it into a compressor. You don't need a huge one.

We have a lay-up bench that I can include too if you're interested. It is attached to the front of the press in the photos and we keep our cassettes stacked there. Cassettes are not included, but I could throw a couple in if you want.

Finally, the adjustable top mold is also included. We've pressed skis and boards from 130cm to over 200cm with this top mold. We can also include one bottom mold to get you started if you need.

I think that's everything. Let me know if you have any questions. I will not part this out. It will only be sold as a complete package.



Asking $3,500 OBO for everything. Shipping not included, but I can load it on to a truck for you if you want to ship it.

I can't get the pictures to link to this forum so please follow the link for pictures
of the press: http://tahoesnowlab.com/ski-press

Press is located at Slant Skis HQ - 1730 River Rd, Tahoe City, CA, 96145

Call, text, or email for more info.

Thanks!!
Josh
530.448.4230
josh@slantskis.com

[img]http://postimg.org/image/ulvzt8upr/[/img]
Back to top
View user's profile Send private message Send e-mail Visit poster's website
MadRussian



Joined: 30 Sep 2010
Posts: 682
Location: USA

PostPosted: Wed Jun 01, 2016 3:45 pm    Post subject: Reply with quote

from the looks of it this press shouldn't be difficult to modified into double-decker
_________________
I have not failed. I've just found 10,000 ways that won't work.
Thomas A. Edison
Back to top
View user's profile Send private message
Slant



Joined: 16 Apr 2009
Posts: 34
Location: North Lake Tahoe

PostPosted: Wed Jun 08, 2016 4:30 pm    Post subject: Reply with quote

MadRussian wrote:
from the looks of it this press shouldn't be difficult to modified into double-decker

Yes, you could add a second area for pressing below the lower beams, but it would be near the floor.
Back to top
View user's profile Send private message Send e-mail Visit poster's website
MadRussian



Joined: 30 Sep 2010
Posts: 682
Location: USA

PostPosted: Thu Jun 09, 2016 3:24 pm    Post subject: Reply with quote

why go down?

I wonder shorten thelegs and add I-beams on top. Modify/change/reinforce vertical support.
I'm not trying to tell you what to do..... We just have a conversation Very Happy
_________________
I have not failed. I've just found 10,000 ways that won't work.
Thomas A. Edison
Back to top
View user's profile Send private message
Slant



Joined: 16 Apr 2009
Posts: 34
Location: North Lake Tahoe

PostPosted: Sun Jun 12, 2016 4:44 pm    Post subject: Reply with quote

Press is sold. It's headed to WA.
Back to top
View user's profile Send private message Send e-mail Visit poster's website
Display posts from previous:   
Post new topic   Reply to topic     Forum Index -> Commercial postings All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


Powered by phpBB © 2001, 2005 phpBB Group