i know this has been covered before, but i need a little extra.
I'm using a 1/2" wood blade, 15 tpi, and jsut destroying it trimming flash. I suspect it's because the offset teeth rub against the edging.
What do other people use? A metal-cutting blade? What width and tpi? Also, I'm assuming that a slower saw speed (1500rpm) is preferable?
Thanks!
Bandsaw Blade for Flash
Moderators: Head Monkey, kelvin, bigKam, skidesmond, chrismp
Sounds like a cheap blade. I don't know but the specs.( 1/2" and 15 tpi) sounds a litlle odd to me. Here is one source of info.
http://www.allbandsawblades.com/nubmer_teeth.htm
What type of bandsaw do you have?
I use a jig saw
http://www.allbandsawblades.com/nubmer_teeth.htm
What type of bandsaw do you have?
I use a jig saw
Hmm sorry to hear. It's obviously for wood, fine wood.
I tried it with a metal blade I have, but then I had the opposite problem. Taking some pieces of the edges off. No good either. So, I'm using my jig saw instead. In my opinion a better way to do it. At least with the blades I have right now.
I'm using the band saw only for my cores and use the roughest blade I could find for that type of band saw. 1/2" and 4 tpi.
If I going to go on with this hobby I will (or have to) by a bigger band saw. More power.
Good luck
I tried it with a metal blade I have, but then I had the opposite problem. Taking some pieces of the edges off. No good either. So, I'm using my jig saw instead. In my opinion a better way to do it. At least with the blades I have right now.
I'm using the band saw only for my cores and use the roughest blade I could find for that type of band saw. 1/2" and 4 tpi.
If I going to go on with this hobby I will (or have to) by a bigger band saw. More power.
Good luck
bandsaw blade
Please check my post from sept. 09. Hopefully it will shed some light. Good luck
Didn't want to start a new topic for that but wanted to share to info with you guys.
First I have to admit I'm a real retard when it comes to using a table saw, I hardly manage to make straight cuts, especially in the ends of long pieces ! It gives me some headaches when I'm in the process of preparing core blanks !
I was looking for quite some time for a great blade for my table saw for when I slice the wood blocks I make to get core blanks.
Previously I was using some pricey all purpose blades (I use my table saw not only for slicing cores...) but yesterday I finally decided to buy a "ripping" blade. I went with the "not that expensive" Freud Diablo ripping blade, I believe it has less than 30 teeth.
Result is pure awesomeness ! I only have a cheap table saw but with this blade it slices 2.5" of ash and maple like if it was butter (well... at least compared to other blades I had..)
I also extended the surface of my table saw, adding a 3' extension on both the front and rear of the saw so my planks are always supported. Also made a 8' long fence (just a MDF leftover) so everything is guided perfectly all the way.
It's not that friendly to install all this setup but the results I got was really worth the trouble.
Now, my core blanks are more precise than before, I go faster, cuts are cleaner and I'm only stressing out when setting everything up, after that it's super easy ! It's still a time consuming process but I have a better control on quality now.
I'll take pictures next time I set all this up ! (won't be soon, I cut enough core blanks for 5 pairs yesterday !)
My next project : a glue spreader. I still can't do it nicely by hand with a "spatula", I've seen in a video some times ago some kind of roller the guy was running his boards onto to have glue applies, then he placed all his planks in a press to laminate them... this roller would be perfect for me !
Basically I think it's an horizontal roller, about 10" wide maximum. It's installed over a container, open on the top with glue in it so the bottom of the roller is always "in the glue"... saw that system for waxing skis also (not with glue obviously).
First I have to admit I'm a real retard when it comes to using a table saw, I hardly manage to make straight cuts, especially in the ends of long pieces ! It gives me some headaches when I'm in the process of preparing core blanks !
I was looking for quite some time for a great blade for my table saw for when I slice the wood blocks I make to get core blanks.
Previously I was using some pricey all purpose blades (I use my table saw not only for slicing cores...) but yesterday I finally decided to buy a "ripping" blade. I went with the "not that expensive" Freud Diablo ripping blade, I believe it has less than 30 teeth.
Result is pure awesomeness ! I only have a cheap table saw but with this blade it slices 2.5" of ash and maple like if it was butter (well... at least compared to other blades I had..)
I also extended the surface of my table saw, adding a 3' extension on both the front and rear of the saw so my planks are always supported. Also made a 8' long fence (just a MDF leftover) so everything is guided perfectly all the way.
It's not that friendly to install all this setup but the results I got was really worth the trouble.
Now, my core blanks are more precise than before, I go faster, cuts are cleaner and I'm only stressing out when setting everything up, after that it's super easy ! It's still a time consuming process but I have a better control on quality now.
I'll take pictures next time I set all this up ! (won't be soon, I cut enough core blanks for 5 pairs yesterday !)
My next project : a glue spreader. I still can't do it nicely by hand with a "spatula", I've seen in a video some times ago some kind of roller the guy was running his boards onto to have glue applies, then he placed all his planks in a press to laminate them... this roller would be perfect for me !
Basically I think it's an horizontal roller, about 10" wide maximum. It's installed over a container, open on the top with glue in it so the bottom of the roller is always "in the glue"... saw that system for waxing skis also (not with glue obviously).
A bad day skiing is always better than a good one at work...
Good with progress! Right? 
You need to make one of theese (if you haven't) http://www.woodworkersguide.com/2010/04 ... ce-insert/ It's called ZCI (Zero Clearence Insert) and makes your cuts even cleaner!
Treat your new blade as a baby! You can use oven cleaner to clean it. The blade, NOT the baby!
Looking forward for some pictures.
Cheers
You need to make one of theese (if you haven't) http://www.woodworkersguide.com/2010/04 ... ce-insert/ It's called ZCI (Zero Clearence Insert) and makes your cuts even cleaner!Treat your new blade as a baby! You can use oven cleaner to clean it. The blade, NOT the baby!
Looking forward for some pictures.
Cheers
-
twizzstyle
- Posts: 2207
- Joined: Tue Mar 07, 2006 8:25 pm
- Location: Kenmore, Wa USA
i got that same blade and maybe I'm a pussy, but i thought it was too aggressive. i cut a cassette out with it and it got nice and dull and now it's perfect.Brazen wrote:The best advice I ever got on this (from Lindsay at SBM) was to use a bi-metal 10-14tpi. It has 2 heights of teeth and it works awesomely, cuts quicker than a hot knife through a butterstick barricade.
Sounds like a glue spreader one would use for pressing skateboards? Seen here around the 2 min mark.ben_mtl wrote:My next project : a glue spreader. I still can't do it nicely by hand with a "spatula", I've seen in a video some times ago some kind of roller the guy was running his boards onto to have glue applies, then he placed all his planks in a press to laminate them... this roller would be perfect for me !
Basically I think it's an horizontal roller, about 10" wide maximum. It's installed over a container, open on the top with glue in it so the bottom of the roller is always "in the glue"... saw that system for waxing skis also (not with glue obviously).