White spots showing through base material.
Moderators: Head Monkey, kelvin, bigKam, skidesmond, chrismp
White spots showing through base material.
I'm working on a project laminating white UHMW to maple veneer and I have pressed many successful ones in past years however this year I have had several come out of the press with white spots visible through the base. I can't seem to determine what the issue is. I have tried more epoxy, less epoxy. We are roughing up the surface and flame treating the base. Could these be air pockets? Any other ideas?
Re: White spots showing through base material.
Looks a bit like air pockets - especially since they clearly occur around the knots you can see in the picture. What type of press are you using?
Re: White spots showing through base material.
Hydraulic cold press.
Re: White spots showing through base material.
yeah I agree with chrismp - in addition to his question - are you providing a way to "bleed" excess epoxy? think of how a typical ski squeezes excess expoxy out the sides when pressed - these could also be epoxy pockets from excess having nowhere to go.
Re: White spots showing through base material.
Agree, looks like air. Increase your pressure and make sure it’s fairly even.
Fighting gravity on a daily basis
www.Whiteroomcustomskis.com
www.Whiteroomcustomskis.com
Re: White spots showing through base material.
Looking at your pic, I think the answer is shown just above the p-tex.
Looks like bubbly cured epoxy.
Could be cavitation from your spreading technique?
Wet out your maple and your base. Try not to whip up any bubbles.
If you're using heat the air will expand and those bubbles have no where to go.
Just my $0.69
sam
Looks like bubbly cured epoxy.
Could be cavitation from your spreading technique?
Wet out your maple and your base. Try not to whip up any bubbles.
If you're using heat the air will expand and those bubbles have no where to go.
Just my $0.69
sam
You don't even have a legit signature, nothing to reveal who you are and what you do...
Best of luck to you. (uneva)
Best of luck to you. (uneva)
Re: White spots showing through base material.
Could be a couple of things then. Your pressure might not be even enough (it's hard to get mold surfaces even and matching perfectly) - to mitigate this, you could use a thin layer of soft material (silicone foam sheets work well as epoxy doesn't stick to them) in the press on top of the base material to get a more even pressure distribution.
Another reason might be your epoxy already kicking before it gets into the press. Check the working time of your epoxy and compare that to how long it takes you to get everything into the press after mixing the epoxy. However, this is not an exact science as working time is usually stated for a mix of 100 grams in a cup - so if you mix significantly more than this and leave it in the cup, it will go off quicker and on the other hand spreading the epoxy on the workpiece will prolong working time if it hasn't already started kicking (i.e. getting too warm).
Re: White spots showing through base material.
How much resin did you use and how much pressure ? Since there is no fiberglass between your wood and your base, could it be possible you squeezed out too much?
Likely problems
Pressure: Too much, too little, or not even
Resin too little or kicked too fast, did you wet both surfaces?
Poor mold conformity maybe
Likely problems
Pressure: Too much, too little, or not even
Resin too little or kicked too fast, did you wet both surfaces?
Poor mold conformity maybe
Fighting gravity on a daily basis
www.Whiteroomcustomskis.com
www.Whiteroomcustomskis.com
Re: White spots showing through base material.
Lots of epoxy squeezes out the sides and ends. It is not trapped by any means.
Re: White spots showing through base material.
We have tried many of these things and did manage to get rid of the white pockets. We ended up using less pressure, more resin, and silicone sheets. The result looks great, unfortunately we are still ending up with some delamination! Again, we're flame treating, cleaning with alcohol, abraiding, etc.chrismp wrote: ↑Wed Nov 30, 2022 3:18 amCould be a couple of things then. Your pressure might not be even enough (it's hard to get mold surfaces even and matching perfectly) - to mitigate this, you could use a thin layer of soft material (silicone foam sheets work well as epoxy doesn't stick to them) in the press on top of the base material to get a more even pressure distribution.
Another reason might be your epoxy already kicking before it gets into the press. Check the working time of your epoxy and compare that to how long it takes you to get everything into the press after mixing the epoxy. However, this is not an exact science as working time is usually stated for a mix of 100 grams in a cup - so if you mix significantly more than this and leave it in the cup, it will go off quicker and on the other hand spreading the epoxy on the workpiece will prolong working time if it hasn't already started kicking (i.e. getting too warm).
Re: White spots showing through base material.
Maybe add some fiberglass veil between you layers to hold resin??
Fighting gravity on a daily basis
www.Whiteroomcustomskis.com
www.Whiteroomcustomskis.com
Re: White spots showing through base material.
There are some things you could try (or a combination). Many epoxies are quite brittle, so adding a bit of flexibilizer can help with delaminations. Make sure to test if the flexibilizer works with your epoxy on a sample!
And as already suggested adding some sort of filler to hold the epoxy, such as fiberglass veil or cotton flocks, should help too.
And as already suggested adding some sort of filler to hold the epoxy, such as fiberglass veil or cotton flocks, should help too.
Re: White spots showing through base material.
I'm sure the OP figured this out by now, but a couple of things to add.
Flame treating with the wrong fuel/air mix can be worse than not flame treating your UHMW, at all. Delam city - learned it the hard way. I don't see that introducing air pockets while curing under pressure, because it should be obvious during layup that your epoxy is beading up and rolling off the plastic.
No idea why the OP isn't using some kind of fiber between the wood and I guess base material? We do the same thing, but pressing thicker sheets of sidewall UHMW to 5mm thick sheets of hardwood to produce sidewall stock that will stay bonded to core blanks through the milling process. We cut the composite sidewall material into narrow strips and I have never noticed air pockets between the layers. If I did, I would assume I had not used enough epoxy, because we're already using high pressure and heat to squeeze out everything we can before it becomes a solid.
Iif your molds aren't true, but you're okay with whatever comes out matching the surface you're pressing against, then try more pressure. If you don't care about adding weight or waste, try using a more generous hand with the epoxy.
Flame treating with the wrong fuel/air mix can be worse than not flame treating your UHMW, at all. Delam city - learned it the hard way. I don't see that introducing air pockets while curing under pressure, because it should be obvious during layup that your epoxy is beading up and rolling off the plastic.
No idea why the OP isn't using some kind of fiber between the wood and I guess base material? We do the same thing, but pressing thicker sheets of sidewall UHMW to 5mm thick sheets of hardwood to produce sidewall stock that will stay bonded to core blanks through the milling process. We cut the composite sidewall material into narrow strips and I have never noticed air pockets between the layers. If I did, I would assume I had not used enough epoxy, because we're already using high pressure and heat to squeeze out everything we can before it becomes a solid.
Iif your molds aren't true, but you're okay with whatever comes out matching the surface you're pressing against, then try more pressure. If you don't care about adding weight or waste, try using a more generous hand with the epoxy.
Melanie
Break over. Back to the... hobby? obsession? labor of love? The whatever that is EVL Skis.![Cool 8)](./images/smilies/icon_cool.gif)
Break over. Back to the... hobby? obsession? labor of love? The whatever that is EVL Skis.
![Cool 8)](./images/smilies/icon_cool.gif)