Slant Skis is Selling Complete Ski Press - Tahoe City, CA
Posted: Mon May 30, 2016 2:33 pm
Hi Ski Builders,
--for pictures-->http://tahoesnowlab.com/ski-press
We are selling our trusty ski press. We have pressed hundreds of pairs of skis with this press. It is in complete working order. The new one we are designing is the same as this, except it will be double decker so we have a more efficient space.
The rigid opening is 18" deep x 11" high x 76" across between the vertical posts. The entire press is 8' across and 67" high. You can press with the entire 8' (240+ cm), but it's easiest to access the mold from the side pressing 200cm + skis.
The press is made of twin I-beams top and bottom. There is 3/16 plate top and bottom, spanning the beams. It is bare steel.
It is on heavy duty casters so you can push it....slowly. It weighs about 1,700 lbs. But you can bring it with you wherever you want to go!
We usually press at about 45 psi. We have calculated the pressure at around 22 tons.
I will include our temperature control setup along with a newer heat mat. We usually press around 180ยบ F. This controller will allow you so set whatever temp you want. It runs off single-phase 220V power for the heat and 110v for the controller.
I will include our 1/2" square tube cat-track.
The industrial grade goodyear fire hoses are included too. Along with the air hoses and pressure gauge. Just plug it into a compressor. You don't need a huge one.
We have a lay-up bench that I can include too if you're interested. It is attached to the front of the press in the photos and we keep our cassettes stacked there. Cassettes are not included, but I could throw a couple in if you want.
Finally, the adjustable top mold is also included. We've pressed skis and boards from 130cm to over 200cm with this top mold. We can also include one bottom mold to get you started if you need.
I think that's everything. Let me know if you have any questions. I will not part this out. It will only be sold as a complete package.
Asking $3,500 OBO for everything. Shipping not included, but I can load it on to a truck for you if you want to ship it.
I can't get the pictures to link to this forum so please follow the link for pictures
of the press: http://tahoesnowlab.com/ski-press
Press is located at Slant Skis HQ - 1730 River Rd, Tahoe City, CA, 96145
Call, text, or email for more info.
Thanks!!
Josh
530.448.4230
josh@slantskis.com
--for pictures-->http://tahoesnowlab.com/ski-press
We are selling our trusty ski press. We have pressed hundreds of pairs of skis with this press. It is in complete working order. The new one we are designing is the same as this, except it will be double decker so we have a more efficient space.
The rigid opening is 18" deep x 11" high x 76" across between the vertical posts. The entire press is 8' across and 67" high. You can press with the entire 8' (240+ cm), but it's easiest to access the mold from the side pressing 200cm + skis.
The press is made of twin I-beams top and bottom. There is 3/16 plate top and bottom, spanning the beams. It is bare steel.
It is on heavy duty casters so you can push it....slowly. It weighs about 1,700 lbs. But you can bring it with you wherever you want to go!
We usually press at about 45 psi. We have calculated the pressure at around 22 tons.
I will include our temperature control setup along with a newer heat mat. We usually press around 180ยบ F. This controller will allow you so set whatever temp you want. It runs off single-phase 220V power for the heat and 110v for the controller.
I will include our 1/2" square tube cat-track.
The industrial grade goodyear fire hoses are included too. Along with the air hoses and pressure gauge. Just plug it into a compressor. You don't need a huge one.
We have a lay-up bench that I can include too if you're interested. It is attached to the front of the press in the photos and we keep our cassettes stacked there. Cassettes are not included, but I could throw a couple in if you want.
Finally, the adjustable top mold is also included. We've pressed skis and boards from 130cm to over 200cm with this top mold. We can also include one bottom mold to get you started if you need.
I think that's everything. Let me know if you have any questions. I will not part this out. It will only be sold as a complete package.
Asking $3,500 OBO for everything. Shipping not included, but I can load it on to a truck for you if you want to ship it.
I can't get the pictures to link to this forum so please follow the link for pictures
of the press: http://tahoesnowlab.com/ski-press
Press is located at Slant Skis HQ - 1730 River Rd, Tahoe City, CA, 96145
Call, text, or email for more info.
Thanks!!
Josh
530.448.4230
josh@slantskis.com
