Juke 2013/2014
Moderators: Head Monkey, kelvin, bigKam, skidesmond, chrismp
-
- Posts: 712
- Joined: Thu Sep 30, 2010 12:32 pm
- Location: USA
-
- Posts: 1148
- Joined: Tue Jan 08, 2008 6:02 am
- Location: NJ USA
- Contact:
-
- Posts: 2204
- Joined: Tue Mar 07, 2006 8:25 pm
- Location: Kenmore, Wa USA
-
- Posts: 86
- Joined: Wed Oct 13, 2010 7:21 am
- Location: Mass
@chrismp I got the 3x8 machine which actually works out to being 6 inches longer in both directions. Over the next couple days I will try to do some tests on the cuts and report back with my findings.
@MadRussian Ya the Bosch Colt has a 1/4 shank, and with my trial cuts I had a 1/4 and 1/2 bit. 3/4 would probably be what I topped out at if I pick one up soon.
@knightsofnii This was my first weekend ever using any of the software or making cuts, but when I cut the core the entire process was smooth with no studdering.
@MadRussian Ya the Bosch Colt has a 1/4 shank, and with my trial cuts I had a 1/4 and 1/2 bit. 3/4 would probably be what I topped out at if I pick one up soon.
@knightsofnii This was my first weekend ever using any of the software or making cuts, but when I cut the core the entire process was smooth with no studdering.
-
- Posts: 86
- Joined: Wed Oct 13, 2010 7:21 am
- Location: Mass
@MontuckyMadman I have no idea if this is the best way to go about this, but for my first time trying to profile the core I used this flute cut.
![Image](http://i1262.photobucket.com/albums/ii617/jukesnowboarding/fasfasd_zpscdf8fa40.jpg)
This was something I just did really quickly so the measurements do not line up, but I figured out where I wanted my profile to occur then drew a line. After that I used the multiple array tool. This allowed me to copy my line and also set the spacing so that the bit I was using would overlap cuts.
![Image](http://i1262.photobucket.com/albums/ii617/jukesnowboarding/flute_zpsdbc64cb6.jpg)
Then I chose the flute depth and correct tool, and ramped over the length of my lines to get a consistent cut to the nose and tail.
Im not sure if that gives you a better idea. And I am open to any and all suggestions, I was trying to see if the machine could do a profile and this was the method I came up with.
Also idk if any of you will find this helpful, but Sean over at Donek shared this with me and it has helped me understand varying bit information.
https://docs.google.com/file/d/0B8GtiBW ... edit?pli=1
![Image](http://i1262.photobucket.com/albums/ii617/jukesnowboarding/fasfasd_zpscdf8fa40.jpg)
This was something I just did really quickly so the measurements do not line up, but I figured out where I wanted my profile to occur then drew a line. After that I used the multiple array tool. This allowed me to copy my line and also set the spacing so that the bit I was using would overlap cuts.
![Image](http://i1262.photobucket.com/albums/ii617/jukesnowboarding/flute_zpsdbc64cb6.jpg)
Then I chose the flute depth and correct tool, and ramped over the length of my lines to get a consistent cut to the nose and tail.
Im not sure if that gives you a better idea. And I am open to any and all suggestions, I was trying to see if the machine could do a profile and this was the method I came up with.
Also idk if any of you will find this helpful, but Sean over at Donek shared this with me and it has helped me understand varying bit information.
https://docs.google.com/file/d/0B8GtiBW ... edit?pli=1
-
- Posts: 1148
- Joined: Tue Jan 08, 2008 6:02 am
- Location: NJ USA
- Contact:
you really got Aspire with the machine?
I have aspire until this computer dies, then I have to go out and buy it again
.
I just cut out the bottom and top pieces for my vacuum hold down table.
Using Aspire made it a pretty easy job.
And yes, now that I'm using a good CAM processor, the machine is cutting nice curves and circles without studdering or stopping. I think it was Lazycam that was taking shortcuts.
I have aspire until this computer dies, then I have to go out and buy it again
![Sad :(](./images/smilies/icon_sad.gif)
I just cut out the bottom and top pieces for my vacuum hold down table.
Using Aspire made it a pretty easy job.
And yes, now that I'm using a good CAM processor, the machine is cutting nice curves and circles without studdering or stopping. I think it was Lazycam that was taking shortcuts.
Doug
-
- Posts: 378
- Joined: Wed Nov 04, 2009 10:59 am
- Location: Portland Area, Maine
- Contact:
-
- Posts: 378
- Joined: Wed Nov 04, 2009 10:59 am
- Location: Portland Area, Maine
- Contact:
-
- Posts: 86
- Joined: Wed Oct 13, 2010 7:21 am
- Location: Mass
-
- Posts: 86
- Joined: Wed Oct 13, 2010 7:21 am
- Location: Mass
-
- Posts: 378
- Joined: Wed Nov 04, 2009 10:59 am
- Location: Portland Area, Maine
- Contact:
"real" jobs can be cool tho! More money to finance the building of stuff!!JukeSnowboarding wrote:I am sorry it has taken so long. Started first "real" job since I graduated college in May, takes up more time than I thought. I will try to have the tests and pictures up this weekend.
I bought one of these last week regardless. Ordered the gantry upgrade and am going with a 2.25hp digital router from craftsmen.