Twizz 2012/2013
Moderators: Head Monkey, kelvin, bigKam, skidesmond, chrismp
- FigmentOriginal
- Posts: 140
- Joined: Mon Oct 24, 2011 1:13 pm
-
- Posts: 2337
- Joined: Tue Apr 07, 2009 3:26 pm
- Location: Western Mass, USA
- Contact:
The see thru thing is not new Burton did that on a few models several years ago. I think they were using aluminum honeycomb....
Not sure how that is done. Yes gimmicky.
Not sure how that is done. Yes gimmicky.
Fighting gravity on a daily basis
www.Whiteroomcustomskis.com
www.Whiteroomcustomskis.com
- FigmentOriginal
- Posts: 140
- Joined: Mon Oct 24, 2011 1:13 pm
-
- Posts: 175
- Joined: Mon Oct 11, 2010 11:06 pm
- Contact:
Pressure difference shouldn't be an issue with a honeycomb core, because the cellules are pretty small. But the rossignol is just a marketing thing I guess. How much weight can you possibly safe by replacing some square inches of the core by a pretty heavy polypropylene honeycomb? And if there is a little too much resin in the prepreg they end up probably at the same weight as if they would use any other core...
-
- Posts: 175
- Joined: Mon Oct 11, 2010 11:06 pm
- Contact:
Pressure difference shouldn't be an issue with a honeycomb core, because the cellules are pretty small. But the rossignol is just a marketing thing I guess. How much weight can you possibly safe by replacing some square inches of the core by a pretty heavy polypropylene honeycomb? And if there is a little too much resin in the prepreg they end up probably at the same weight as if they would use any other core...
Hey Twizz,
not sure if I should post here or on the newer thread but since the subject has been talked about in the previous page...
I have a couple questions regarding your drag knife / die-cut bases.
- I'm looking at some drill blank to try and make a drag knife. Locally I was only able to find some 1/4 drill rod, 3ft long and it is some "W1 or O1 type steel". It's more expensive than McMaster at $7/3ft but McMaster won't ship to me anyways... Not sure it's the right stuff though since this steel grade is supposed to be water or oil hardened (I won't be able to make a heat treatment at home...)... any input on that ?
- When you do a die-cut base, what do you use to hold the different pieces together ? Meditape ? Isn't there any problem when you have a "separation line" that crosses an edge ? Any detailed info on that would be great !
Thanks !
not sure if I should post here or on the newer thread but since the subject has been talked about in the previous page...
I have a couple questions regarding your drag knife / die-cut bases.
- I'm looking at some drill blank to try and make a drag knife. Locally I was only able to find some 1/4 drill rod, 3ft long and it is some "W1 or O1 type steel". It's more expensive than McMaster at $7/3ft but McMaster won't ship to me anyways... Not sure it's the right stuff though since this steel grade is supposed to be water or oil hardened (I won't be able to make a heat treatment at home...)... any input on that ?
- When you do a die-cut base, what do you use to hold the different pieces together ? Meditape ? Isn't there any problem when you have a "separation line" that crosses an edge ? Any detailed info on that would be great !
Thanks !
A bad day skiing is always better than a good one at work...
-
- Posts: 2204
- Joined: Tue Mar 07, 2006 8:25 pm
- Location: Kenmore, Wa USA
Not sure about the rod material... the blanks I got from mcmaster are solid carbide, I thought. This issue with McMaster not shipping to canada seems to come up a lot. Is there no other industrial supply place in canada that might stock something like this?
I'm trying to find the exact thing I ordered from McMaster, but I've got a lot of McMaster emails to go through I remember it only being a few dollars for a 1/8" rod, 2-3" long. I could easily order a few and then mail it to you.
I've only done a base once that had multiple colors (the foam core skis with the maps on top, bottoms are orange with STUMPYSTICKS in yellow). I did use medipore tape to hold it all together (a lot of it...).
What I did was cut out all the letters first and assemble it as one big sheet, and taped it up with the medipore. Then I cut out the base shapes. It held together reasonably well, and once I had the edges glued on it was pretty solid. I'll never do that many shapes again though, that was a lot of work.
I just drag-knived the bases for my new skis a few days ago, and man... for such a quick hand-grown tool, it does amazing work!
I've done a little experimenting to try to get a good "blade" shape so it cuts clean, but still casters properly. Works great for me, and just putting the blade in the router spindle works great.
I'm trying to find the exact thing I ordered from McMaster, but I've got a lot of McMaster emails to go through I remember it only being a few dollars for a 1/8" rod, 2-3" long. I could easily order a few and then mail it to you.
I've only done a base once that had multiple colors (the foam core skis with the maps on top, bottoms are orange with STUMPYSTICKS in yellow). I did use medipore tape to hold it all together (a lot of it...).
What I did was cut out all the letters first and assemble it as one big sheet, and taped it up with the medipore. Then I cut out the base shapes. It held together reasonably well, and once I had the edges glued on it was pretty solid. I'll never do that many shapes again though, that was a lot of work.
I just drag-knived the bases for my new skis a few days ago, and man... for such a quick hand-grown tool, it does amazing work!
I've done a little experimenting to try to get a good "blade" shape so it cuts clean, but still casters properly. Works great for me, and just putting the blade in the router spindle works great.
Nice ! thank you.
After some search on McMaster I believe this (http://www.mcmaster.com/#3009a127/=p1nk2e) is what you might have ordered from them, which is not what I can source locally... I'll look into it.
You made your drag knife from some 1/8" rod ? my smallest chunk on the router is 1/4" so I'll go with 1/4".
...I'm wondering if I could just take a 1/4" drill bit, cut the "flutes" part and make the tool from that... would be easier to source a drill bit than a drill blank !
After some search on McMaster I believe this (http://www.mcmaster.com/#3009a127/=p1nk2e) is what you might have ordered from them, which is not what I can source locally... I'll look into it.
You made your drag knife from some 1/8" rod ? my smallest chunk on the router is 1/4" so I'll go with 1/4".
...I'm wondering if I could just take a 1/4" drill bit, cut the "flutes" part and make the tool from that... would be easier to source a drill bit than a drill blank !
A bad day skiing is always better than a good one at work...
yep, I already sent them an e-mail to see what they have, no answer yet.
All the companies that would have what I need are very expensive + they request a 100$ minumum order (the ones I found on the internet and got answers from, at least...)
I'm really digging the drill bit repurpose though...
All the companies that would have what I need are very expensive + they request a 100$ minumum order (the ones I found on the internet and got answers from, at least...)
I'm really digging the drill bit repurpose though...
A bad day skiing is always better than a good one at work...
-
- Posts: 2204
- Joined: Tue Mar 07, 2006 8:25 pm
- Location: Kenmore, Wa USA
Ah, that is another consideration, you can only go as small as your smallest chuck!
What kind of router do you have? I have a Porter Cable and got a collet kit, so I have a 1/8" collet.
http://buildyourcnc.com/item/router-col ... collet-kit
And yeah, grinding down a 1/4" drill bit should work fine! You just need to get the shape right, so the blade is small, positioned right for good castering, and... SHARP!
My best cartoon of what it might look like on a 1/4" bit:
What kind of router do you have? I have a Porter Cable and got a collet kit, so I have a 1/8" collet.
http://buildyourcnc.com/item/router-col ... collet-kit
And yeah, grinding down a 1/4" drill bit should work fine! You just need to get the shape right, so the blade is small, positioned right for good castering, and... SHARP!
My best cartoon of what it might look like on a 1/4" bit:
-
- Posts: 2204
- Joined: Tue Mar 07, 2006 8:25 pm
- Location: Kenmore, Wa USA
I have an Hitachi M12VC router... I guess I'm about to pull the trigger on a collet kit, It's gonna help with a (very small) runout problem I have with the factory collet... being able to put a 1/8" bit / DIY drag knife just make the decision easier to take...
It looks like precisebits (where I take the collet kit) also sells "calibration blanks", which might well be useful to shape a drag knife... I'll ask for the alloy type and hardness.
I like to think this "compulsive buys" are some kind if investment... yeah right ! nothing in skibuilding is an investment.. it's just a money pit.
..and CNC building is even worse :p
It looks like precisebits (where I take the collet kit) also sells "calibration blanks", which might well be useful to shape a drag knife... I'll ask for the alloy type and hardness.
I like to think this "compulsive buys" are some kind if investment... yeah right ! nothing in skibuilding is an investment.. it's just a money pit.
..and CNC building is even worse :p
A bad day skiing is always better than a good one at work...