Search found 265 matches
- Sat Sep 16, 2006 8:22 pm
- Forum: Ski/Snowboard Design and Layup
- Topic: know a composite engineer?
- Replies: 1
- Views: 2651
know a composite engineer?
any engineers out there? I am working on my engineering degree hoping to get a degree in Composites Engineering. The current problem is that my school requires that we interview someone in our desired major. Anyone have a composites or plastics engineering degree that would be willing to let me inte...
- Sat Sep 16, 2006 7:19 pm
- Forum: Equipment and Tools (e.g., ski press, core profiler, etc)
- Topic: Heat Blanket
- Replies: 28
- Views: 23872
- Sat Sep 16, 2006 4:57 pm
- Forum: Equipment and Tools (e.g., ski press, core profiler, etc)
- Topic: Pressurized vacuum press design
- Replies: 3
- Views: 4578
yes, i can see that HDPE will be safer...polyethelene has the ability to be cold formed which makes it much more shatter proof. but as far as the seal goes, even if they seal one side, you are going to have to be able to open and close the other side (in order to insert and remove your vacuum layup)...
- Sat Sep 16, 2006 12:47 pm
- Forum: Equipment and Tools (e.g., ski press, core profiler, etc)
- Topic: Questions regarding heating blankets and vacuum pressing
- Replies: 5
- Views: 7599
- Sat Sep 16, 2006 12:41 pm
- Forum: Equipment and Tools (e.g., ski press, core profiler, etc)
- Topic: Heat Blanket
- Replies: 28
- Views: 23872
So if I have a controller that sends out an AC relay signal...i should find an SSR that has an AC input and output? is there a benefit to having a DC signal over an AC signal? I recently purchased the Omron E5CJ and an SSR with DC input, AC output. the problem is that when i went to wire everything,...
- Sat Sep 16, 2006 12:35 pm
- Forum: Equipment and Tools (e.g., ski press, core profiler, etc)
- Topic: Pressurized vacuum press design
- Replies: 3
- Views: 4578
- Fri Sep 15, 2006 8:32 pm
- Forum: Archive
- Topic: We need your opinion about SB logo design
- Replies: 25
- Views: 45211
- Mon Jan 09, 2006 9:31 pm
- Forum: Ski/Snowboard Design and Layup
- Topic: Homemade prepregs?
- Replies: 4
- Views: 4335
Homemade prepregs?
As the subject may have lead you to believe, i have been toying with the idea of making my own prepregs...is this feasable? Anyone have any experience doing this? I am hoping its as simple as resining a bunch of sheets of glass or carbon, then sandwiching them between release film and sticking them ...
- Wed Jan 04, 2006 6:42 pm
- Forum: Ski/Snowboard Design and Layup
- Topic: Edge HELP
- Replies: 3
- Views: 4094
Edge HELP
We just finished gluing another set of edges on another base with the same failed results, the base deforms itself severely under the force of the edges. We preform the edges with a propane torch and a CNCed template. We also cut out the base using a CNCed template. Despite all this, this is our sec...
- Mon Jan 02, 2006 10:29 am
- Forum: Ski/Snowboard Design and Layup
- Topic: A flaw in our theory...
- Replies: 4
- Views: 4895
A flaw in our theory...
Normally i post at Graf, but I build skis...so needless to say I was pretty excited when i found your site. So here is a "puzzle" that i found that has been bothering me, hopefully you have the answer: I was recently reading my new composite construction book (my christmas gift to myself) ...