Search found 12 matches
- Wed Nov 07, 2012 9:41 am
- Forum: Materials and Supplies
- Topic: Topsheet protective film- what do you use?
- Replies: 6
- Views: 5880
- Thu Nov 01, 2012 9:36 am
- Forum: Materials and Supplies
- Topic: Topsheet protective film- what do you use?
- Replies: 6
- Views: 5880
Topsheet protective film- what do you use?
Just curios what brand and where some of you get your protective film to protect the topsheet during layup? I've used tape, but thought it would be nice to have a solid cover. Couldn't find anything specific searching! Thanks!
- Tue Aug 09, 2011 7:34 am
- Forum: Yard Sale (non commercial)
- Topic: Snowboard inserts
- Replies: 6
- Views: 4801
- Sun Feb 13, 2011 9:55 pm
- Forum: Materials and Supplies
- Topic: Epoxy and bubbles and syringes
- Replies: 3
- Views: 2106
Thanks for the info.. As for the the vacuum pump, I read somewhere a foodsaver would do the job, so today I mixed carefully and vacuum sealed the thing and noticed the bubbles surfacing. I guess the problem/question I have now, after I mix the resin and hardener can I set in front of a heat source t...
- Fri Feb 11, 2011 2:04 pm
- Forum: Materials and Supplies
- Topic: Epoxy and bubbles and syringes
- Replies: 3
- Views: 2106
Epoxy and bubbles and syringes
I looked for a topic on bubbles but didn't find what I was looking for. I need to fill a small groove and I'm using a syringe, problem is I'm getting a ton of bubbles. I'm using west system g/flex if that makes a difference. Thanks again!
- Fri Feb 11, 2011 1:57 pm
- Forum: Materials and Supplies
- Topic: ski edge step question
- Replies: 3
- Views: 2367
- Thu Feb 10, 2011 10:11 pm
- Forum: Materials and Supplies
- Topic: ski edge step question
- Replies: 3
- Views: 2367
ski edge step question
I know the edges that the ski builders store sells has a 1.33mm step, can you buy edges with more of a step?
- Tue Jan 25, 2011 9:49 am
- Forum: Ski/Snowboard Design and Layup
- Topic: Split Board Inside edge question
- Replies: 12
- Views: 7995
I ended up messing with this just a bit on suday night, and think I have it figured out for the most part. I was able to find a board at a pawn shop for $20 so we had something to throw a couple experiments at. For this one we actually used a table saw to cut the grooves I needed and it went well, t...
- Fri Jan 14, 2011 7:07 pm
- Forum: Ski/Snowboard Design and Layup
- Topic: Split Board Inside edge question
- Replies: 12
- Views: 7995
- Fri Jan 14, 2011 4:32 pm
- Forum: Ski/Snowboard Design and Layup
- Topic: Split Board Inside edge question
- Replies: 12
- Views: 7995
skidesmond- Did you route that out on a table or by hand? I'm thinking the camber would affect the cut if routed on a table, maybe not. as far as filling the gap goes, I think because it won't be tapered like a normal sidewall but at a 90 degree angle the edge will actually have material over it. Go...
- Fri Jan 14, 2011 8:30 am
- Forum: Ski/Snowboard Design and Layup
- Topic: Split Board Inside edge question
- Replies: 12
- Views: 7995
Thanks for the input and pictures. I was going to try and find a few boards on craigslist for cheap to try on but maybe I'll just get some base material and glue to the base of a 1x and try it that way? I wonder if the heat from the bit would ill affect the base material? I was thinking I would have...
- Thu Jan 13, 2011 9:35 am
- Forum: Ski/Snowboard Design and Layup
- Topic: Split Board Inside edge question
- Replies: 12
- Views: 7995
Split Board Inside edge question
First of all this website is pretty killer! I searched through everything I couldn't find the answer I was looking for, sorry if you've seen this question before! I want to install an inside edge on some DIY splitboards and I was hoping to get some advice from guys that work with this stuff more tha...